CALL 24 HOURS / 7 DAYS A WEEK

Milwaukee Metro: (414) 327-7049

All  Other Area's: (262) 240-0757

Enjoy All The Benefits of A Care Free Maintenance Plan

1. Having a HVAC Preventive Maintenance Plan saves you money
2. Your system will get checked yearly to help prevent costly repairs
3. Your equipment will be running its peak optimum level after Tune-Up is Complete
4. Priority Service and discounted pricing on parts and labor if repair is necessary
5. Maintain Service History Documentation
6. All Tune-Up’s & Inspections are always performed by our NATE Certified Technicians

NOTE: We can also build you a "Custom Maintenance Plan", just give us a call and we can put together a plan specific too your needs and budget.

Equipment Approved For Maintenance Agreement: Furnace's, Hot Water Boilers, Steam Boilers, Standard AC Systems, Magic-Pak Heat / Cool Systems, Unico AC Systems, SpacePak AC Systems, High Velocity AC Systems, Air Handlers and Humidifiers.

 CARE FREE MAINTENANCE AGREEMENT TERMS & CONDITIONS

• Tune-Up / Inspection of Equipment will be done prior to approval
• Equipment must be in normal operating condition for approval of agreement
• Equipment is covered for ONE FULL YEAR from the date of purchase including all the benefits from your package
• Care FREE Maintenance Agreement stays with the home it was purchased for and will not transfer to your new home
• Agreement may be transferred to new owner upon home sale
• No portion of the payment is refundable due to sale or transfer of home ownership

Furnace Tune-Up / Inspection Checklist

1. Clean furnace
2. Check Venting
3. Check Drain Lines / Trap
4. Clean and check pilots
5. Adjust pilot
6. Check Thermocouple
7. Check burners
8. Check fan belts
9. Check amperage draw
10. Check furnace filters
11. Check safety devices
12. Check thermostat
13. Check limit control
14. Inspect combustion chamber
15. Check blower wheel
16. Check blower motor
17. Check furnace wiring
18. Check for combustion air
19. Check gas valve operation
20. Test for gas leaks
21. Check electrical connections
22. Inspect heat exchanger for CO leaks
23. Check any/all accessories 
    

Air Conditioner Tune-Up / Inspection Checklist

1. Blower Motor – measure amperage and voltage for proper operation
2. Thermostat – test for proper operation
3. Check existing air filter
4. Bearing – inspect for wear and lubricate
5. Check indoor coil
6. Check Condensate Drain
7. Inspect Condenser Coil
8. Refrigerant – monitor operating pressures
9. Safety Devices – inspect for proper operation
10. Electrical Disconnect Box – inspect for proper rating and safe installation
11. Electrical Wiring – inspect and tighten connections
12. Test/inspect contactors for burned, pitted contacts
13. Inspect electrical for exposed wiring
14. Inspect and test capacitors
15. Inspect fan blade
16. Inspect service valves for proper operation
17. Measure Supply/Return temperature differential
18. Compressor – monitor, measure amperage and volt draw and wiring connections
19. Check Condenser Fan Motor
20. Check for Freon Leaks
    

Boiler Tune-Up / Inspection Checklist

1. Clean Boiler
2. Check Venting
3. Check Drain Lines / Trap (Only on High Efficiency Boilers)
4. Clean and check pilots
5. Check All Radiators
6. Adjust pilot
7. Check Thermocouple
8. Check burners
9. Check Circulation Pumps
10. Check amperage draw
11. Check Fill Valve
12. Check Expansion Tank for Proper Operation
13. Check safety devices
14. Check thermostat
15. Check limit control
16. Inspect combustion chamber
17. Check Backflow Preventer
18. Check Operation of Pressure Relief Valve
19. Check Boiler wiring
20. Check for proper combustion air
21. Check gas valve operation
22. Test for gas leaks
23. Check electrical connections
24. Inspect heat exchanger
25. Check for Soot Build up in Heat Exchanger
26. Check any/all accessories

Steam Boiler Tune-Up / Inspection Checklist

1. Inspect general condition of system
2. Check for appropriate supply of fresh air into room
3. Listen for odd sounds while unit is in operation
4. Check Venting going into Chimney
5. Test Low Water cut off
6. Flush all of Boiler Drains and low water cut off
7. Check site glass for damage / flush and clean
8. Check all safety devices
9. Check for gas leaks
10. Inspect burners for rust, dirt and signs of damage
11. Make sure burners are relocked in their slots and seated on the burner orifices
12. Check gas pressure
13. Vacuum burner box
14. Check and tighten all electrical connections
15. Check Main Air Vent for proper operation
16. Check Radiator Air Vents
17. Check pressure
18. Check Fill Valve
19. Check Back Flow Preventor
20. Check for Soot Build up in Heat Exchanger
21. Check Thermostat
22. Check safety devices